BAT, WLC (HiLCOS)
-
HiLCOS Client with Radius CA, username and password
Published: Nov 15, 2019
Nov 15, 2019 -
How to change WPA key simultaneously on a large amount of AP
Published: Feb 21, 2018
Feb 21, 2018 -
How to use your own HTML pages for the Public Spot
Published: Feb 9, 2018
Feb 21, 2018 -
How to do a single or multiple firmware upgrade on HiLCOS devices via LANconfig
Published: Feb 9, 2018
Feb 21, 2018 -
How to do a firmware upgrade on HiLCOS devices via the web interface
Published: Feb 9, 2018
Feb 21, 2018 -
How to stop the Wireless interface if the network cable isn't plugged in
Published: Feb 9, 2018
Feb 21, 2018 -
How to optimize passive scan
Published: Feb 9, 2018
Feb 9, 2018 -
How to setup Auto-WDS feature
Published: Feb 9, 2018
Feb 21, 2018 -
How to create a trace output
Published: Feb 9, 2018
Feb 21, 2018 -
How to setup accounting (WLC/Openbat)
Published: Feb 9, 2018
Feb 21, 2018 -
How to store an alternate configuration
Published: Feb 9, 2018
Feb 9, 2018 -
How to create a TCP port tunnel with the BAT
Published: Feb 21, 2018
Feb 21, 2018 -
How to filter ARPs on the BAT
Published: Feb 21, 2018
Feb 21, 2018 -
How to load a feature license in a WLC or a BAT
Published: Feb 21, 2018
Feb 21, 2018 -
HiLCOS Quick Start Guide
Published: Nov 15, 2019
Nov 15, 2019 -
BAT450-F Quick Start Guide
Published: Nov 15, 2019
Nov 15, 2019 -
WLC - How to Install a Cluster License
Published: Nov 4, 2019
Nov 4, 2019 -
How To Optimize Roaming for AGV on BAT867 and BAT-R
Published: Oct 22, 2018
Oct 22, 2018 -
BAT867-R Punkt-zu-Punkt-Konfigurationsleitfaden
Published: Jun 28, 2018
Jun 16, 2021 -
Roaming Parameters Infographic
Published: May 22, 2018
May 22, 2018 -
How to find the SNMP OIDs for HiLCOS Settings
Published: May 22, 2018
May 22, 2018 -
HiLCOS - How to check the Signal Strength (for each Antenna)
Published: May 22, 2018
May 22, 2018 -
How to Debug BAT Devices
Published: May 7, 2018
May 7, 2018 -
How to replace a WLC backup CA running in a cluster
Published: Feb 21, 2018
Feb 21, 2018 -
How to configure the Public Spot function on the WLC
Published: Feb 9, 2018
Feb 21, 2018 -
How to use 802.11e (prioritization) on the Open BAT WLAN interfaces
Published: Feb 9, 2018
Feb 9, 2018 -
How to configure GRE Tunnel on the Open BAT
Published: Feb 9, 2018
Feb 21, 2018 -
How to configure IP masquerading on the OpenBAT
Published: Feb 9, 2018
Feb 21, 2018 -
How to apply a WLAN profile on Access Points and customize it for each AP
Published: Feb 9, 2018
Feb 21, 2018 -
So konfigurieren Sie eine Open BAT als 802.1x-Supplicant
Published: Feb 9, 2018
Jun 9, 2021 -
So konfigurieren Sie eine Open BAT als 802.1x-Authenticator
Published: Feb 9, 2018
Jun 9, 2021 -
How to configure an Open BAT as Access Point
Published: Feb 9, 2018
Feb 21, 2018 -
How to configure an Open BAT as Access Client
Published: Feb 9, 2018
Feb 21, 2018 -
How to configure a Radius Profile on the WLC and include it in Logical settings
Published: Feb 9, 2018
Feb 21, 2018 -
How to add a BAT or a WLC in LANconfig
Published: Feb 9, 2018
Feb 21, 2018 -
How to configure routing on the BAT ?
Published: Feb 9, 2018
Feb 21, 2018 -
How to configure L2 firewall rule on the BAT
Published: Feb 9, 2018
Feb 21, 2018 -
How to allow the 40MHz usage for channels 167-171 ?
Published: Feb 9, 2018
Feb 9, 2018 -
How to redirect Broadcast when the BAT is used as router
Published: Feb 9, 2018
Feb 21, 2018 -
How to use RPCAP as a high resolution polling tool for RSSI measurement
Published: Feb 9, 2018
Feb 21, 2018 -
How to determine the managed Access Points behavior in case the controller fails
Published: Feb 9, 2018
Feb 9, 2018 -
How to set date and time on a BAT or on a WLC
Published: Feb 9, 2018
Feb 21, 2018 -
How to create a WLC cluster
Published: Feb 9, 2018
Feb 21, 2018 -
How to give an Open BAT or a WLC an IP address ?
Published: Feb 9, 2018
Feb 21, 2018 -
So verwenden Sie einen Open BAT oder WLC als RADIUS-Server und richten Benutzerkonten ein
Published: Feb 9, 2018
Jun 9, 2021 -
How to migrate a configuration from a Bat-54 to an OpenBat
Published: Feb 9, 2018
Feb 21, 2018 -
How to remotely capture the trafic of an Open BAT interface with RPCap function and Wireshark
Published: Feb 9, 2018
Feb 21, 2018 -
When a client roams from an AP to another one. How are the FDB of the switches behind the AP updated ?
Published: Feb 9, 2018
Feb 21, 2018 -
How to use Radius to access the BAT's agent
Published: Feb 9, 2018
Feb 21, 2018 -
How to configure L3 roaming with a WLC ?
Published: Feb 9, 2018
Feb 21, 2018